Nice workmanship!

Posted on 04/10/2009 by Thomas K. - 2003 Ford Mustang (Leander,TX)

3 of 5 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"The product is very nice, and the quality of the workmanship is outstanding. Nice finish on product also."

Was this review helpful? Yes No

JBA SHORTIES/MID-LENGTH

Posted on 04/15/2008 by Ted L. - 1966 Ford Mustang (Cerritos,CA)

3 of 3 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Good Headers but clearance issues on driverside my 66/289 and another note: Changing a few of the plugs is a pain in the _____ and some speciallty tools may need to be used."

Was this review helpful? Yes No

Great product

Posted on 02/03/2008 by Randal T. - 2005 Ford Mustang (San Jose,CA)

4 of 8 people found the following review helpful.

"One always is concerned about how aftermarket parts are going to fit as well as work. These JBA Cat4ward headers, while time consumming to install, fit beautifully. I'm very please. When doing this change-out, I recommend doing it iin combination with replacement of your "H" pipe to an "X" pipe."

Was this review helpful? Yes No

JBA Headers mustang 4.0

Posted on 12/29/2007 by Bart C. - 2005 Ford Mustang (Lake Worth,FL)

2 of 5 people found the following review helpful.

"The order process was simple, quick and efficent. I was keep informed on the order process until they arrived a week later. All the necesssary parts were enclosed in the box. The directions were a little vague, however it was not difficult to figure out. JBA does want you to remove the O2 sensors but I suggest removing the spark plug boots as well to save the cost or replacing the plug wires. The directions tell you to remove the existing studs from the engine and to replace them with the suppliied bolts, this is a slight pain. The haders were not that difficult to install but I highly recommend a lift not the drive on ramps. We were lucky enough to use the rack at the local high school auto shop. There is a definite sound difference cannot tell you about gas milage yet as the car was down due to a broken plug wire, We are up and running and I will let you know. Overall I am very pleased with the headers and rating AutoAnything they would get 10 STARS"

Was this review helpful? Yes No

Opps, close but not quite

Posted on 12/25/2007 by Roger S. - 1966 Ford Mustang (La Plata,MD)

1 of 5 people found the following review helpful.

"Beautiful headers, but it turns out that they wil not fit the Mustang '66 289 ci California A.I.R. block that I have. I did not see see any disclaimer when I ordered them that they would not fit. Oh'well, I will have to contact AutoAnything to return them. But, as I noted earlier, they look great and I hope to get a set from AutoAnything that fits. Also, the AutoAnything overall website was easy to use and the price was very competitive."

Was this review helpful? Yes No

Great headers but almost impossible to install

Posted on 10/08/2007 by John B. - 2001 Ford Mustang (Spartanburg,SC)

4 of 4 people found the following review helpful.

"They look great and will make your cold air intake sound great, but it took 9 hours with 3 people to install. It seems ford makes it very hard to work on the headers. We had to take out the air intake and the master cylinder was in the way. If you can, the best way to do it is to take out the engine out of the engine bay to install it."

Was this review helpful? Yes No

JBA Cat4Ward for 4.0L Mustang

Posted on 07/28/2006 by David H. - 2006 Ford Mustang (Orlando,FL)

2 of 2 people found the following review helpful.

"The headers went on quite easy with little difficulty. I've felt a little bit of gains with them and I can hear the engine alot better with them on and it seems rev a bit quicker. I'm happy to have only paid $589 for them instead of $640 because I don't think they are worth THAT much. I'm very happy with them though and they should come in handy MUCH more with an F/I."

Was this review helpful? Yes No

JBA Headers - 2008 Nissan Frontier V6 4x4

Posted on 10/30/2009 by Marcos E. - 2008 Nissan Frontier (Severn,MD)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Installed along with the JBA exhaust. They do take time to install, at least a good days worth. Most of the time is consumed taking the old ones off. Did NOT have to remove engine mount bolts. They look good and my exhaust system sounds great. Would recommend to other owners if you did the work yourself.. I can't imagine how much a regular mechanic would charge for all that labor!"

Was this review helpful? Yes No

4L sohc ranger

Posted on 10/29/2009 by David H. - 2001 Ford Ranger (Round Lake Beach,IL)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Good looking headers. Noticable power increase with my Gibson cat back system. Had them professionaly installed and I'm glad. New bracket for the dip stick had to be fab'd and some creativity was needed for the EGR connection as well."

Was this review helpful? Yes No

Awesome

Posted on 10/27/2009 by William B. (Newton,NJ)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"THEY SOUND GREAT AND LOOK GOOD"

Was this review helpful? Yes No