We’re sorry. The information you have requested is temporarily unavailable.
Carriage Works Billet Grille Part #43602 Customer Reviews
16 Customer Reviews
Reviewed by n.Damon G (Kelso, WA) Reviewed for a 2008 GMC Sierra — Apr 18, 2013 2:22 PM
I bought another grill somewhere else and it was made of really soft aluminum and would bend just looking at it. This grill was strong and sturdy and from the looks of it on and off the truck, very well built.
Reviewed by Raymond C (Raymond, WA) Reviewed for a 2008 GMC Sierra — Dec 14, 2012 9:10 PM
Fit and finish was excellent, and install was pretty easy. Took just under 2 hours from start to finish including cutting the old grill out. Install is easiest if you remove the grill and bumper cap as one unit and separate them off the truck.
Reviewed by JACK M (Gresham, OR) Reviewed for a 2017 Ford F-150 — Dec 28, 2009 11:02 AM
The Carriage Works Billet Grille a beautifully crafted accessory. It fits our 2008 GMC Sierra like a glove. The quality of The Carriage Works Billet Grille is easily discernible when compared side by side with other brands. We selected the "replacement billet grille". It's a little more difficult to install as compared to the "bolt over" type, but it's well worth the effort as this style looks much better in my opinion.
Reviewed by Jared T (Ellsworth AFB, SD) Reviewed for a 2009 GMC Sierra — Nov 03, 2009 12:41 PM
Installation was fairly simple, the hardest part being taking off the bumper shell, just have to give it a good tug and it pops right off. Other then that everything went smoothly, highly recommended.
Reviewed by Ashley A (Providence Village, TX) Reviewed for a 2008 GMC Sierra — Jun 09, 2009 10:10 PM
I have been searching for a billet grill for a while and have really only found the overlays that keep the original grill intact and/or keep the GMC logo. So when I found this one, I jumped on it. The install was okay, but could get a little hairy if you have not done 100+ of these like I have. There is just a lot to take off to get the grill out (no fault to Carriage Works but rather GM idioengineering) and the shell becomes flimsy and hard to handle when you cut out the center. But once you get the hang of it, the install becomes fairly simple. My only complaint is that I wish there were more bars on the grill like the old Trenz grilles. But other than that, it makes the truck really stand out! Heck, only 2 days after installing it, I had a guy ask if I could install one for him!!!
Reviewed by Michael V (Hayward, CA) Reviewed for a 2008 GMC Sierra — Feb 13, 2009 12:40 PM
I received the billet grill for my 2008 GMC very quickly after my online order. It looks great on my truck as opposed to the ugly standard grill with the big red "GMC" stuck in the middle. I would advise not following the directions for installation however. Taking the entire grill frame out after disconnecting the upper bumper trim etc.etc.is not only none productive but NOT necessary. I just left the grill in place and used a "Kobalt" flat blade handsaw to remove the center and then a Dremmel tool to sand the rough edges down. After doing so the grill bolted easily into place with the provided hardware. The total installation time was cut in half by using this technique and it looks professionally done!
This part has been discontinued by Carriage Works . We apologize for the inconvenience.View all options for this product
- carriage works grills
- carriage works ram grille bumper
- carriage works 3d mesh
- carriage works 41833
- billet ford grille emblem
- dodge truck grills
- ford ranger black mesh grill
- lexus rx350 2009 grill
- billet grills for 1988 chevrolet s-10
- chevrolet truck emblems
- chip for truck
- rain guards for auto windows
- led headlight bulbs for cars