JBA Cat4ward Headers

03 sierra cat4ward jba headers 14 gage nickel plated shortys

Posted on 06/26/2008 by Daren T. (Cape Canaveral,FL)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Great product. Used customer sevice very fast service, obuve and beyond. Results big performance differance mpg not tested yet."

Was this review helpful? Yes No

The right tools make it easier!

Posted on 06/12/2008 by Eric R. - 2000 Ford Ranger (Santa Ana,CA)

1 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Great throttle response, really smooth throttle. Also installed are a K&N intake kit and a magnaflow exhaust. A 13mm ratchet wrench is a must when installing these headers. As a matter of fact find as many 13mm tools as you can and a couple of extensions to complete this install. And another note about the install remove the steering shaft for the driver's side. Haven't had it long enough to tell gas mileage difference but it does look a little better. Same goes for the towing/hauling."

Was this review helpful? Yes No

Overall Great Deal for The Money

Posted on 05/31/2008 by Christine A L. - 2004 Ford F-150 (Lowman,NY)

2 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"We are thrilled with the performance the extra gas mileage and the cool power! It would be nice to have a JBA Cat4ward Header sticker to put on the vehicle to let everyone know is such a hot performer!"

Was this review helpful? Yes No

2007 Dodge Nitro JBA shorty headers

Posted on 05/14/2008 by Christopher K. - 2007 Dodge Nitro (Glenview,IL)

1 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"THese headers looked great and installed easily. Big notice in throttle response. Overall a great add on for my Nitro."

Was this review helpful? Yes No

08 GMC SIERRA 5.3

Posted on 05/08/2008 by Garret B. - 2008 GMC Sierra (Baltimore,MD)

1 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I strongly suggest the purchase of a 1/2" 15mm deep, 6-point and swivel adapter for your extention prior to trying to remove the factory exhaust. It took just 3 hours (could have been two or less with a 6-point). My only complaint about the new is the stuggle to secure the passenger side collector around the cat. Not much change in tone, better responce for passing-mid to high rpm. 8000 miles so far no leaks, no loose bolts, very impressed with direct fit"

Was this review helpful? Yes No

JBA HEADERS

Posted on 04/22/2008 by Rene G. - 2006 Toyota Tacoma (Burbank,CA)

2 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"the headers arrived the next day!! The JBA headers sound really good with a deep throaty sound, perfect addition to my magnaflow cat back and K&N intake... it really opens up your engine around 3000 rpm"

Was this review helpful? Yes No

JBA SHORTIES/MID-LENGTH

Posted on 04/15/2008 by Ted L. - 1966 Ford Mustang (Cerritos,CA)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Good Headers but clearance issues on driverside my 66/289 and another note: Changing a few of the plugs is a pain in the _____ and some speciallty tools may need to be used."

Was this review helpful? Yes No

jba headers

Posted on 03/31/2008 by Rashid A. - 2005 Chrysler 300 (Springfield Gardens,NY)

1 of 4 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"This product is very good one my friend got on his charger 2005 hemi . acctully he told me about it . Its really give a huge diffrent than the oem one in hp & torque Iam glad to use this product and glad to deal with you .And i have one question .Is the JBA Y pipe fixed on the shorty headers thank you"

Was this review helpful? Yes No

Worth the work

Posted on 03/26/2008 by Owen J. - 2001 Ford F-150 (Black Hawk,SD)

0 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"It took me a full day to install the headers, but they are work the work and money. There is a definite increase in torque and horsepower, and a decrease in RPMs by about 500-1000 (60mph). I haven't had a chance to see about improved fuel mileage, but am guessing it should increase a little also."

Was this review helpful? Yes No

JBA Cat4ward Headers -smog legal

Posted on 03/17/2008 by Sebastian D. - 2004 Chevy Silverado (San Francisco,CA)

1 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Good quality product. Nice thick flanges. Had to remove drive shaft to install. The Headers got a little scratched during install. The trucks tone is noticeably deeper."

Was this review helpful? Yes No

Great product

Posted on 02/03/2008 by Randal T. - 2005 Ford Mustang (San Jose,CA)

2 of 5 people found the following review helpful.

"One always is concerned about how aftermarket parts are going to fit as well as work. These JBA Cat4ward headers, while time consumming to install, fit beautifully. I'm very please. When doing this change-out, I recommend doing it iin combination with replacement of your "H" pipe to an "X" pipe."

Was this review helpful? Yes No

JBA Headers mustang 4.0

Posted on 12/29/2007 by Bart C. - 2005 Ford Mustang (Lake Worth,FL)

1 of 4 people found the following review helpful.

"The order process was simple, quick and efficent. I was keep informed on the order process until they arrived a week later. All the necesssary parts were enclosed in the box. The directions were a little vague, however it was not difficult to figure out. JBA does want you to remove the O2 sensors but I suggest removing the spark plug boots as well to save the cost or replacing the plug wires. The directions tell you to remove the existing studs from the engine and to replace them with the suppliied bolts, this is a slight pain. The haders were not that difficult to install but I highly recommend a lift not the drive on ramps. We were lucky enough to use the rack at the local high school auto shop. There is a definite sound difference cannot tell you about gas milage yet as the car was down due to a broken plug wire, We are up and running and I will let you know. Overall I am very pleased with the headers and rating AutoAnything they would get 10 STARS"

Was this review helpful? Yes No

Headers

Posted on 12/26/2007 by Richard T. - 2006 Jeep Liberty (West Wyoming,PA)

1 of 4 people found the following review helpful.

"Just opened them on Christmas the quality and workmanship are excellent!!!!!!!!!!There nicer than the ones on my Camaro. Rick"

Was this review helpful? Yes No

Opps, close but not quite

Posted on 12/25/2007 by Roger S. - 1966 Ford Mustang (La Plata,MD)

0 of 3 people found the following review helpful.

"Beautiful headers, but it turns out that they wil not fit the Mustang '66 289 ci California A.I.R. block that I have. I did not see see any disclaimer when I ordered them that they would not fit. Oh'well, I will have to contact AutoAnything to return them. But, as I noted earlier, they look great and I hope to get a set from AutoAnything that fits. Also, the AutoAnything overall website was easy to use and the price was very competitive."

Was this review helpful? Yes No

JBA HWADERS

Posted on 12/19/2007 by Ralph B. - 2007 Chevy Silverado (Stockton,CA)

5 of 7 people found the following review helpful.

"JBA Headers, gave me more power off the line, cant tell any differance in gas mileage, no diff in sound, seems to run smoother, All together in a nut shell, it run`s better and is faster.JBA Headers, K&N Cold Air Intake Dual Flow Master`s Super Chip."

Was this review helpful? Yes No

2004 Silverado Crew - 5.3L, 2wd

Posted on 12/19/2007 by Dana H. - 2004 Chevy Silverado (Lakeland,FL)

6 of 8 people found the following review helpful.

"Installed the titanium ceramic coated JBA headers on my Silverado last week. High quality product with good fit & finish. Installed in 6 hours with myself and one other semi competant person. Biggest PITA was getting the factory manifolds off. After that the install was fairly easy. Noticed some improvement throughout the rpm range. I wouldn't call it a huge improvement but definately stronger than before. Only previous mod was a Corsa cat-back. Sound didn't incrase much with the headers. Haven't been able to check mileage yet but it seems about the same."

Was this review helpful? Yes No

Nice Pair

Posted on 11/16/2007 by Victor M. - 1993 Ford Cobra (Salinas,CA)

0 of 2 people found the following review helpful.

"I was really happy to see them arrive. I was even more surprised at the quality these headers show. I will definitely buy another set for my mustang cobra."

Was this review helpful? Yes No

good quality, good looks, ?better power?

Posted on 11/16/2007 by Johnathon A. - 2000 GMC Truck 1500 (Abilene,TX)

1 of 3 people found the following review helpful.

"A friend and I installed these in about seven hours. Here are some things I learned, (1.) Remove the wheels and the inner fender splash guards, it makes things much easier (2.) SATURATE the old bolts with penetrate and let it soak in (3.) Have someone or something pull down on the respective collector pipes when removing and installing the manifolds. I was expecting a bigger power increase, but I'm still satisfied."

Was this review helpful? Yes No

Great product!

Posted on 11/09/2007 by Peter R. - 2004 Cadillac Escalade (Leesburg,VA)

1 of 5 people found the following review helpful.

"These headers add a noticeable increase in power all throughout the rpm range but can be felt especially in the mid to upper rpm's. They don't make the exhaust any louder either which is a bonus."

Was this review helpful? Yes No

JBA Headers 4my FJ Cruiser

Posted on 11/05/2007 by Sergio Z. - 2007 Toyota FJ Cruiser (National City,CA)

5 of 6 people found the following review helpful.

"For real, you can feal the difference,I have convined with a Flowmaster and the sound is very nice, you can feal the Power of the 4.0 engine,110%"

Was this review helpful? Yes No

Nice Fit

Posted on 11/03/2007 by Carlo P. - 1999 Chevy Tahoe (Medford,NY)

1 of 1 people found the following review helpful.

"Probably one of the best and easiest headers I have ever installed. The 14ga stainless steel is nice and heavy and meant to last. Welds are perfect as well as the fit onto the OEM collector. I have noticed that the engine breaths easier. My choice of finish was the plain stainless. It darkened up a bit and looks good. Personally I feel the other coatings are just for looks and don't justify the cost. I highly recommend JBA Headers."

Was this review helpful? Yes No

JBA Headers

Posted on 11/02/2007 by Max M. - 2007 Toyota FJ Cruiser (Weatherford,TX)

1 of 1 people found the following review helpful.

"Worth it"

Was this review helpful? Yes No

Great headers but almost impossible to install

Posted on 10/08/2007 by John B. - 2001 Ford Mustang (Spartanburg,SC)

1 of 1 people found the following review helpful.

"They look great and will make your cold air intake sound great, but it took 9 hours with 3 people to install. It seems ford makes it very hard to work on the headers. We had to take out the air intake and the master cylinder was in the way. If you can, the best way to do it is to take out the engine out of the engine bay to install it."

Was this review helpful? Yes No

2007 chevy tahoe 5.3L

Posted on 10/05/2007 by Paola P. - 2007 Chevy Tahoe (Guatemala,Guatemala)

2 of 2 people found the following review helpful.

"Very easy to install, took about 4 1/2h. Titaniuim ceramic coated, the finish is ok,it has some rough cuts inside the collector though. Great sound when floored, and some power gain mostly in mid to high rpms (my guess is 8-10hp). I still have the original catback, so their potential may not be exploted. Overall, very pleased."

Was this review helpful? Yes No

JBA headers-04 Avalanche

Posted on 10/03/2007 by Douglas O. - 2004 Chevy Avalanche (West Des Moines,IA)

1 of 1 people found the following review helpful.

"The JBA ceramic headers I purchased looked great and sounded equally nice. i could feel a difference in power with the headers in place.The price,shipping time,and finished product I would rate excellent."

Was this review helpful? Yes No