Average Customer Rating |
 (74)
|
| Appearance |
 |
| Ease of Installation |
|
| Price/Value |
 |
| Quality |
|
Sort By
Extend-a-Fender installation on 2000 Toyota Tacoma
Posted on 11/07/2009 by Robert D. - 2000 Toyota Tacoma (Monument,CO)
0 of 0 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"Installation instructions are clear. Bushwacker flares use existing holes and inserts in fenders...a plus. Flares fit very snug against the truck's fenders. Be careful not to overtorque screws as the plastic inserts are very easy to strip. Holes in middle of left rear(LR) flare should be further from edge of flare making flare fit tighter to fender. I had to enlarge the hole to get a tight fit. Recommend installing LR flare last so you can see how the others fit. Check alignment of the LR flare closely before drilling. Other three flares were good and tight."
Was this review helpful? Yes
No
About Robert D.
Vehicle
2000 Toyota Tacoma
I use my vehicle for
Travel and offroading
Posted on 10/05/2009 by Albert V. - 2004 Dodge Ram (Bishop,TX)
0 of 0 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"I’ve wanted to purchase extenda flares since I’ve owned the truck, however, I had a hard time parting with $400 plus dollars. Bought them on sale, under $400 plus dollars, and installed them after I put new rubber all the way around. Couldn’t be happier, the front tires rub just a bit, but it’s still worth the money.
Respectfully,
Al
Bishop, TX"
Was this review helpful? Yes
No
About Albert V.
Vehicle
2004 Dodge Ram
I use my vehicle for
Everything, hunting to date night.
No problem installation! Even a caveman can do it.
Posted on 06/27/2009 by Chris P. - 1997 Toyota Tercel (Berryville,AR)
1 of 1 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"Even though I didn't want to put them on...I had too due to wide tires throwing road mud up on side of truck.
I had them painted to match truck. Installation was straight forward and easy. Did not run into any problems. Total time was approx. 21/2 hours start to finish. Was working in 97 degree heat.
Overall very good product, fast shipping, exactly as advertised!"
Was this review helpful? Yes
No
About Chris P.
Vehicle
1997 Toyota Tercel
I use my vehicle for
Daily Driver
Posted on 04/22/2009 by Casey C. - 2009 Dodge Ram (Ontario,OR)
0 of 3 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"After painting it was a very easy install."
Was this review helpful? Yes
No
About Casey C.
Vehicle
2009 Dodge Ram
I use my vehicle for
everything
great service and quality
Posted on 03/30/2009 by Doyle H. (Gatlinburg,TN)
0 of 0 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"I haven't installed my flares yet. waiting on the humidity to drop a little so i can paint them but it looks like the will be easy to install an the service was great"
Was this review helpful? Yes
No
About Doyle H.
I use my vehicle for
to get back an forth to work an to pull my camper
08 2500 Ram extend-a-fender
Posted on 03/10/2009 by Jack T. - 2008 Dodge Ram (Edinboro ,PA )
3 of 3 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"I installed a set of(4)extend-a-fender flares on my 2008 Dodge ram 2500. Installation was pretty easy (took about 1 1/2 hrs...not working hard)and the flares look great on my truck and do a good job protecting the truck body from dirt and mud. I would recommend these flares to anyone wanting to enhance appearance or protect their truck."
Was this review helpful? Yes
No
About Jack T.
Vehicle
2008 Dodge Ram
I use my vehicle for
Commercial snow plowing, Haul firewood, Daily driver
Easy installation and quality time with my son
Posted on 01/16/2009 by Ashley J. - 1997 Ford F-250 (Lebanon,TN)
2 of 3 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"The flares were fairly easy to install with the only problems being cutting the original side moulding (No big deal there with a sharp knife). The instructions did say to use a hair dryer but a heat gun is what you need. I had my son help me hold things which was very helpful he's eight so getting to help was a big deal. they look great and fit the sides just like factory flares would have. I have gotten several compliments on the looks."
Was this review helpful? Yes
No
About Ashley J.
Vehicle
1997 Ford F-250
I use my vehicle for
Commuting, towing, landscaping, travel, outdoor hobbies
Posted on 10/31/2008 by Kenny J. - 2008 Ford F-150 (Brooksville,FL)
7 of 8 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"Very easy to install, took only 45 min. Look great and work good to keep the rocks off my paint on my 2008 F-150"
Was this review helpful? Yes
No
About Kenny J.
Vehicle
2008 Ford F-150
Posted on 06/12/2008 by James P. (Chicago,IL)
10 of 10 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"The installation was easy but the instructions could be better. They required no drilling.
I agree with other reviewers in that they seem pricey for plastic or else I would have given a perfect score.
Delivery was really fast also.
They look great!"
Was this review helpful? Yes
No
Posted on 04/25/2008 by Jeffrey F. - 2004 Ford F150 (Bellevue,MI)
8 of 11 people found the following review helpful.
Appearance
Ease of Installation
Price/Value
Quality
"They were easy to install. They fit the vehicle perfectly. They look great."
Was this review helpful? Yes
No
About Jeffrey F.
Vehicle
2004 Ford F150