Jet Performance Module

Easy Power

Posted on 05/27/2008 by Cory M. - 1997 Dodge Ram (Kapolei,HI)

1 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I purchased the Jet Performance Chip and installed it along with an AEM Brute Force cold Air Intake, MSD spark plug wires, and Bosch Platinum +4 Spark Plugs. The difference in performance was immediate. I have a 1997 Dodge 1500 4x4 with the 5.2L engine and it roars. the chip took about 30 seconds to install and I am pretty happy so far."

Was this review helpful? Yes No

Jet chip on a 07 dodge ram 1500 w/hemi

Posted on 05/23/2008 by Susan H. - 2007 Dodge Ram (Briones,CA)

2 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"took less than 5 min to install, noticed a difference immediately with shifting and overall performance. I have had this on my vehicle for over 2 weeks and to my surprise I also gained over 3 mpg."

Was this review helpful? Yes No

Instant power

Posted on 05/22/2008 by Jason K. - 2002 Ford Ranger (Sherwood,OR)

6 of 7 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I dont have any baseline numbers or access to a dyno, but I do know that before the chip one of my coworkers with a 1.8ltr Intergra could keep up and barely pass me going up the steep hill to my bosses house. After the chip I am leaving him in the dust. Money well spent. Fairly easy to install."

Was this review helpful? Yes No

Jet Performance Chips Stage 2 PCM

Posted on 05/20/2008 by David D. - 2005 Chrysler 300 (Pembroke,MA)

2 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"My 2005 Chrysler 300C 5.7 liter had just under 30,000 miles on it when I installed the Jet Stage 2 chip in conjunction with a K & N Typhoon intake. I had the stock exhaust resonator replaced with a pair of Magnaflow glass packs and I installed the the recommended 180 degree thermostat, which I had to get from another vendor. The performance increase is breathtaking. The Jet Chip performs as advertized. Now for the bad news. The chip is very difficult to install on the Chrysler 300. I had to trim away a 2" X 1/4" section from the lip of the firewall to get the engine control module back into place after plugging in the chip. After getting the module back into position, the plug with the Jet Chip in it is pressed up very tightly against the firewall insulation. If I had to do it over again I would have trimmed some of the insulation away to relieve pressure on the plug and the PCM. It certainly won't come unplugged now. According to Jet, intsallation of the Stage 2 PCM absolutely necessitates the replacement of the stock 203 degree thermostat with a 180 degree unit. Auto Anything didn't have the thermostat so I had to get it elsewhere which took more time. Other than these two minor complaints I love the performance increase and I can't wait to take the car to "Street Night" at New England Dragway."

Was this review helpful? Yes No

08 dodge ram V6

Posted on 05/19/2008 by Jason O. - 2008 Dodge Ram (Knoxville,TN)

2 of 5 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Buy one, I love mine"

Was this review helpful? Yes No

Jeremy

Posted on 05/16/2008 by Jeremy B. - 2004 Dodge Ram (Jefferson City,TN)

1 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I puchesed one for a Dodge Ram 1500. I noticed a difference as sonn as i started it. It gave it a deeper tone and better take off in between gears for a manual. It was certainly worth the money"

Was this review helpful? Yes No

Stage 1 for 2008 Ford Fusion

Posted on 05/16/2008 by Terry M. - 2008 Ford Fusion (Woodbury,NY)

7 of 9 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Install was approx 1 hour. Had to remove battery, battery tray and CPU completely to install. Manual was outdated and not helpful. Tech support was equally clueless. CPU is located behind battery on the firewall. The chip plugs into top port. The chip has improved mileage on highways but horrible on city roads no other changes noted in terms of tranny shifting and power. JET mass air sensor was also installed."

Was this review helpful? Yes No

slight increase

Posted on 05/15/2008 by Shawn P. - 2001 Dodge Ram (Taylorsville,UT)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"The Jet Performance PCM gives noticeable increase in acceleration. Now that I have added a winch and other heavy accessories to my vehicle the Jet Performance Chip has eliminated any sluggishness I might have otherwise encountered."

Was this review helpful? Yes No

Jet Performance Chip 2003 Dodge Ram

Posted on 05/15/2008 by Calvin I. - 2003 Dodge Ram (Long Beach,CA)

0 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"The Jet performance chip was easy to install and I could immediately feel the enhanced performance. My truck has more torque and also seems to idle better. I can't wait to take a trip to see if my gas mileage improves."

Was this review helpful? Yes No

Not what i expected..

Posted on 05/13/2008 by Matthew K. - 2005 Chevy Colorado (Blythe,CA)

1 of 4 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I expected a little more. It sayed on the website that the chip gives about 20-25hp and i only received 9-12. It helped my torque a small amount as well but still quite what i expected, i can hardley tell the difference."

Was this review helpful? Yes No

My expereince with the Jet Chip for 2006 PT Cruiser

Posted on 05/13/2008 by Steven C H. - 2006 Chrysler PT Cruiser (Haughton,LA)

6 of 7 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"First off I got the Staage I chip for a 2006 PT Cruiser. My mileage has increased about 2-2 1/2 mpg. I am now getting highway mileage in town. I haven't tested performance as of yet because of the price of gas I am trying to take it easy for now. I like the fact that I don't have to use premium gas with the stage I. The only problem is with installing the chip. It is not as easy as the instructions say for this particular install. There is ZERO clearance for the chip between the computer board and the brake fill resivor cap. removal of the computer module or modification of the wiring harness is necessary. Even with the modification the wiring harness is pressing on the neck of the cap and the cap has to be forced into place. This was not the case on my '99 Wrangler. I was simply unplug the harness, place the chip, and replug the harness. I wish the Crusier had been that east."

Was this review helpful? Yes No

Jet Chip Stage 2 - 2008 Dodge Nitro R/T 4.0L -Great Product

Posted on 05/12/2008 by Dennis E. (Calgary,AB)

0 of 0 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Just as advertised - easy to install and great performance boost immediately. Torque and power increase very noticeable - the way it should have come from the factory. Highly recommended for anyone looking to get more jump for your Nitro and get better mileage. It doesn't get better than that. Dennis"

Was this review helpful? Yes No

Not pleased

Posted on 05/10/2008 by David F. (Jasper,GA)

1 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Very little performance difference! No gas milage difference!"

Was this review helpful? Yes No

Not bad for the money...

Posted on 05/07/2008 by Gregory B. - 2007 Jeep Grand Cherokee (Sutersville,PA)

2 of 4 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"It actually raised my mileage to .3 miles per gallon so eventually it will pay itself off in awhile. Little boost in performance too. I am sure it will help if I had an intake to get which I will be getting soon..."

Was this review helpful? Yes No

Jet chip for 07 ford fusion 3.0L V6

Posted on 05/06/2008 by Brian W. - 2007 Mazda Miata/MX-5 (La Verne,CA)

4 of 5 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"07 Ford Fusion 3.0L The chip works good but the install instructions were poor. But for those of us that like to go over 100mph I would strongly suggest getting the speed governer removed, because this chip makes it that much quicker to get over 100MPH! TESTED Times 1/8 mile with out chip 10.381@69mph With JET CHIP 1/8 mile 9.983@72mph"

Was this review helpful? Yes No

Jet Stage II in 1993 Wrangler YJ

Posted on 05/04/2008 by Charlie F. - 1993 Jeep Wrangler (Madisonville,TN)

1 of 3 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"After installing the Jet Stage II, I have noticed an increase in both horsepower and torque in the low to mid-range on my 1993 wrangler YJ, 5 speed, 4.0. This is ideal for my use as I am more concerned with its ability on the trails in low range than with high speed highway use. Although it is a daily driver, it rarely sees much interstate miles. Haven't had much time to check fuel mileage yet, but should gain some due to not being in the gas as much when accelerating. Great product!"

Was this review helpful? Yes No

disappointed

Posted on 05/03/2008 by Fred F. - 2006 Chevy Silverado (Greenville,TX)

6 of 8 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"shortly after recieving my chip, I installed it. Expecting better performance & better gas mileage was the reason for purchase. I CAN'T feel any added performance & gas mileage is about the same."

Was this review helpful? Yes No

05 Hemi Jeep Cherokee

Posted on 05/01/2008 by Jeffery T. - 2005 Jeep Grand Cherokee (Whiteford,MD)

2 of 2 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Worth the money for the fuel savings alone.( If you can keep your foot off the pedal) Installation took approx. 25 minutes. Gained 2-3.5 mpg on fuel mileage on the highway and 2 around town. Noticable gain in power also."

Was this review helpful? Yes No

4.7L Quadcab w/ 45RFE Tranny

Posted on 05/01/2008 by John R. - 2002 Dodge Dakota (Maryland Heights,MO)

6 of 6 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Arrived on time and it was easy to install. Stage 1 with no modifications. Similar results to what others experienced with the same set up and power plant. Noticable difference in performance. Improved low end performance with less lag in throttle response. Better take off from complete stop. There is a definite improvement in the midrange power band when driving in heavy traffic. Approx 500 miles driven since instilation 70% in town. Fuel milage increased from 11.5 mpg city to 14.3 mpg city. Not enough milage driven on long trips to see it there will be an improvement over the previous 18 mpg on the highway. Purchased to improve fuel economy and towing. Would definitely recomend for similar vehicle set up."

Was this review helpful? Yes No

good

Posted on 05/01/2008 by Rick D. (Modoc,IN)

0 of 1 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"like it"

Was this review helpful? Yes No

Works Well on 1996 Dodge Ram 1500 4x4 manual

Posted on 04/28/2008 by Scott C. - 1996 Dodge Ram (Jay,FL)

8 of 10 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"I installed the chip with fair ease. took all of ten minutes. I didn't like the fact I couldn't use my dust cover for the computer after I installed the chip, but I guess it will be alright. I did notice a bit of pick up and smoothness to the acceleration after the installation, so I guess advancing the ignition curve did help."

Was this review helpful? Yes No

2004 GMC SIERRA 2500HD

Posted on 04/27/2008 by Richard S. (Merrimack,NH)

5 of 7 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"POWER CHIP COUPLED WITH JET MASS AIR FLOW SENSOR AND A K&N AIR FILTER. POWER INCREASE IS NOTICABLE, HOWEVER NOT AS I HOPED. MILAGE SEEMS TO HAVE INCREASED ABOUT 1/2 MILE PER GALLON."

Was this review helpful? Yes No

little expensive

Posted on 04/26/2008 by Andy L. - 1999 Ford Ranger (Medicine Lodge,KS)

5 of 5 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"too expensive for what it does"

Was this review helpful? Yes No

Dodge 4.7 install

Posted on 04/23/2008 by Donald P. (Macungie,PA)

5 of 5 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"Smooth power from idle all the way up to 5500 rpm, getting a consistent .5 miles extra per gallon anly a 5 minute install,"

Was this review helpful? Yes No

1995 Ford F150 5.0L

Posted on 04/23/2008 by Jon E V. - 1995 Ford F-150 (Alva,FL)

9 of 11 people found the following review helpful.

Appearance

Ease of Installation

Price/Value

Quality

"If I had any idea what I would have to go through to get to the ECM on this vehicle, I would never have purchased the chip. The control module is located between the driver side kick panel and the fender, behind the emergency brake. To get to the module, you have to remove the nuts from the engine side of the firewall, and slide the unit out into the engine compartment, plug the cip in, then re-install the ECM into the firewall. I had to remove the plastic fenderwell to get enough room to slide the ECM out. The chip may have added a little spunk to the engine, but it is not really that noticable. I may notice a difference if I took it out, but I am not curious enough to go through the hassle."

Was this review helpful? Yes No